No, this model does not include a battery or charger. This is an electric tool.
The Worx Leaf Mulcher weighs 20Ibs (9.07 kg) It’s sturdy and stable when set up, yet still light enough to make it easily portable.
Since the Worx 13 Amp Leaf Mulcher is designed for easy and compact storage when not in use, it’s shipped to you in the same configuration. Assembling the Leaf Mulcher is quick, easy and requires no tools!
Assembling the Leaf Mulcher will only take a couple of minutes and will not require any tools! Remove the mulcher from the box and locate the stand. Insert the legs into the stand. Make sure the release button is aligned and locks into position. Place the stand on stable ground. Attach the collection bag of your choice (not included). For plastic, roll the opening of the bag over the top of the stand. For paper leaf collection bags (12-16” (30.48 cm) diameter), use the included support ring. Place the orange motor housing on the stand. Fit the black funnel onto the motor housing and lock the clamps to secure it. Place the funnel cover on top, align the white dots on each piece and lock the tabs to secure the cover in place. Before plugging it in, add the cutting lines by feeding it through the holes on the spinner head and align the ends so they are even. Push each end through the corresponding ferrule and repeat for the other side. Plug in your Leaf Mulcher and you’re ready to go!
We don’t recommend storing your Leaf Mulcher outside. It’s designed to quickly and easily disassemble for compact storage.
Turn off your Worx 13 Amp Leaf Mulcher and unplug it. Separate the individual pieces and release security latches. Remove the motor housing from the funnel. Detach the legs from the stand by pushing the locking buttons and pulling to release. Turn the stand upside down. Put the funnel into the stand. Fit the motor housing into the funnel. Place the funnel cover on top of the motor. The legs will fit into the notches in the funnel cover. That’s it! You’re ready to store your Leaf Mulcher until it’s time to use it again.
Your mulcher is designed to work with cutting line and will not accommodate any type of metal blades.
Before proceeding, turn off and unplug your Leaf Mulcher for safety. Remove the mulcher funnel and funnel cover. Cut the old lines and remove them from the spinner head. Thread one piece of line through one set of feed holes on top of the spinner head. Make sure the ends of the line are even. Thread both ends of the line through the corresponding ferrule. Repeat for the other side. The built-in line cutter will make sure that your lines are always the right length.
While there are several steps to clean the air filter, it will only take a few minutes. Unplug the Leaf Mulcher. Once it is unplugged, detach the funnel from the motor housing. Flip the motor housing so the cutting head faces the ground. Remove the six screws from the sides of the motor cover. They are located on the outside edges of the motor cover. The filter is located flush against the power switch. It can be removed and cleaned. When replacing the motor casing, squeeze the casing inward slightly to allow the casing to lock back in place. Reinsert the six screws and tighten. Flip the motor housing over and reattach the funnel.
The right extension cord will ensure you get the performance you expect and will extend the life of your mulcher. Look for an extension cord rated for Outdoor Use and make sure the gauge of the cord is appropriate for the length you’re using. The WG430 is a 120V, 13 Amp tool, so check for gauge and length on the grid here, or in your manual. Your local hardware or garden supply store will be happy to help you select the right cord to meet your needs.
Carefully review the owner’s manual for all safety information and guidelines. Follow safety precautions while using any power tools – including wearing safety eyewear, gloves, appropriate shoes & clothing, and keeping hair tied back. See the owner’s manual for complete safety instructions and details.
You can download the manual here. Our friendly customer service team will be glad to answer any questions you may have at 1-866-354-9679 (Worx).
If you decide the Worx Leaf Mulcher isn’t the right tool for you, we offer a 30-day Money Back Guarantee from date of receipt (less shipping and handling). Please call our customer service center at 1-866-354-9679 (WORX) and we’ll be happy to assist. View more information here.
We know your tools are indispensable, so we cover each tool with a 2 Year Limited Consumer Warranty. You can extend your warranty to 3 years by registering online within 30 days of purchase. Already have your Leaf Mulcher? Register now!
Parts subject to normal wear and tear are not covered by the tool’s warranty. View more information on our warranty here.
Need more line? Lose your bag holder? Many accessories are available online under Accessories.