20V Power Share ExacTrack 6-1/2" Circular Saw

Yes, this model includes 1 battery and 1 charger.

At only 5.9 lbs with the battery installed the ExacTrack is surprisingly lightweight, but make no mistake, it delivers all the power you expect from a circular saw.

The ExacTrack gives you exactly what you expect in a traditional circular saw, and more and with the lightweight, ergonomic experience you expect from Worx. You still get the cutting efficiency of a 6-1/2” blade, and the ability to make bevel cuts up to 50°.

Where ExacTrack shines is the innovative feature that allows you to make flush cuts. Instead of measuring out your cut, then calculating the difference between the outside edge of the blade guard and where the blade cuts, then lining up a guard, ExacTrack cuts out all the extra work. Make your measurements, then line up ANY guide up to 1” thick right on the line. No calculations, no second measurements, and no mistakes! Engage the ExacTrack feature, set the saw on the guard and make a flush cut along your pre-measured line. ExacTrack puts confidence and accuracy in your hand in half the time.

Like all Worx tools, we focus on the experience of using the tools as much as the innovation behind them. ExacTrack is designed with real world use in mind. Switching ExacTrack between standard cutting mode and guided flush cutting is as easy as flipping a switch. Literally.

At the back of the base plate under the battery is a red switch with two positions. Use Standard for a standard cutting mode. Flip the switch to ExacTrack to unlock the red base plate. Line up your cutting guide (up to 1” thick”) along your cutting line and stabilize appropriately. Rest the red area of the baseplate on your guide, turn on the saw and cut. It’s that simple.

When you’re ready to use the standard cutting mode, simply flip the switch back to Standard and enjoy all the same features as a traditional circular saw.

NOTE: For your safety, we recommend removing the battery before switching the tool between cutting modes.

Of course! The ExacTrack is capable of making bevel cuts up to 50° and plunge cutting up to 2” thick.

To bevel cut, make sure the ExacTrack is in Standard cutting mode by checking the switch at the back of the cutting base. Then, loosen the base plate bevel lock knob at the front of the tool and adjust the angle of the base plate to match your desired bevel angle. Tighten the bevel lock knob, and you’re ready to cut.

To plunge cut, make sure the ExacTrack is in Standard mode and the bevel gauge is set at 0. Loosen the cutting depth lock knob (to left of the battery on the side of the tool) and move the baseplate to the desired depth. Tighten the cutting depth lock knob to secure it in place. Rest the front of the base plate on the work surface. Turn the saw on and plunge into your cutting surface.

In standard, 90° cutting mode, ExacTrack can cut materials up to 2-5/32” thick. At a 45° bevel, the cutting capacity is 1-17/32” thick.

When it comes to cutting, the blade determines the material your ExacTrack can tackle. Included, you’ll receive a carbide-tipped wood cutting blade, but you can customize to the job at hand by picking a blade to fit your needs. ExacTrack can use any 6-1/2” blade with a 5/8” arbor, which can be found at any hardware and home improvement store.

With the spindle lock and on-board storage for the allen key, changing the blades on the ExacTrack is quick and easy. Remove the battery. Press the spindle lock button and use the allen key to loosen the blade bolt. Unscrew and remove the blade bolt, and the outer flange. Slide back the safety guard and insert the blade. Once completely seated, install the flange and blade bolt, finger tightening into place. Use the allen key to secure the bolt, re-install the battery, and you’re ready to go.

The Worx ExacTrack circular saw uses 6-1/2” circular saw blades with a 5/8” arbor. Customize your ExacTrack by picking the blade most appropriate for the job at hand. These blades can be purchased at most local hardware or home improvement stores.

Yes! The ExacTrack features a vacuum port on board and includes an adaptor to fit the most common workshop vacuums.

Yes! With Power Share, you can share the battery and save money. Your ExacTrack 20V 6-1/2” Circular Saw can use any Worx 20V battery you already have. By sharing the battery between tools, you’ll always have the power you need to complete any job.

Check out the full line of 20V PowerShare tools here.

It takes approximately 5 hours to fully charge the battery. Additional fast charging options are available.

The 20V Worx MAX Lithium battery included with the Worx ExacTrack 20V 6-1/2” Circular Saw is the same battery we trust to power the JawSaw, and our Cordless Compact Circular saw, among others, like the Hydroshot and Switchdriver. Since the battery can stand up to those high-powered applications, you can trust it to keep up with you in the ExacTrack.

Our lithium tools and Ni-Cd tools are separate platforms and are not interchangeable. Lithium batteries offer our customers maintenance-free technology without the hassle of managing the memory effect inherent in Ni-Cad batteries.

While Power Share allows you to share batteries between tools within the same voltage family, batteries should only be used with tools of a corresponding voltage. Use your 20V MAX Lithium battery with any 20V WORX tool – even the garden tools – but save your 32V battery for your 32V tools.

Your battery will take you far, but if you need more, Worx offers higher capacity batteries, like our 20V 4.0Ah batteries, that are compatible with the ExacTrack as well as faster chargers.

Carefully review the owner’s manual for all safety information and guidelines. Follow safety precautions while using any power tools – including wearing safety eyewear, gloves, appropriate shoes & clothing, and keeping hair tied back. See the owner’s manual for complete safety instructions and details.

ATTENTION: For safety, remove the battery when changing the blades or changing the tool between modes. When changing the blade, we recommend wearing gloves.

You can download the manual here.

Our quick start video tour of the ExacTrack is also available on YouTube.

If you decide the Worx ExacTrack 20V 6-1/2” Circular Saw isn’t the right tool for you, we offer a 30-day Money Back Guarantee from date of receipt (less shipping and handling). Please call our customer service center at 1-866-354-9679 (WORX) and we’ll be happy to assist. View more information here.

We know your tools are indispensable, so we cover each tool with a 2 Year Limited Consumer Warranty. You can extend your warranty to 3 years by registering online within 30 days of purchase. Already have your ExacTrack? Register now!

Worx batteries are covered by a 1 Year Limited Consumer Warranty and are not eligible for warranty extension.

Parts subject to normal wear and tear are not covered by the tool’s warranty. View more information on our warranty here.

Need an extra battery? Many replacement parts are available online under Accessories.