MAKERX 3-Piece Crafting Tool Kit
WA7151 TECHNICAL SPECIFICATIONS
WA7231 TECHNICAL SPECIFICATIONS
WX745L.9 TECHNICAL SPECIFICATIONS
WX746L.9 TECHNICAL SPECIFICATIONS
Product Number 2 TECHNICAL SPECIFICATIONS
WA1551 TECHNICAL SPECIFICATIONS
The USB LED Flex Light works with USB Type-A charging ports.
The USB LED Flex Light requires input of 5V 80MA minimum.
The USB LED Flex Light has three brightness settings, rated at 54/33/20 lumens.
Both models adapt 20V battery power for the MAKERX crafting tools. The HubX includes a USB charging outlet and belt clip.
Any Worx 20V Power Share™ battery will work with the HubX.
The cord reaching from the HubX portable power source to the MAKERX crafting tools is 4 feet long.
No, the HubX is strictly designed to power the MAKERX series of crafting tools, along with a 20V Power Share™ battery.
The MAKERX ZipSnip will cut cardboard, chipboard, corrugated plastic, clamshell or plastic packaging, landscape cloth, plastic sheeting, pond and shower liners, and thick fabric. This rotary cutter will also trim metal and nylon screening, chicken wire, vinyl flooring, and carpet.
New cutting blades will be available on Worx.com and other retailers. The model number for the
for the MAKERX ZipSnip Rotary Cutter is .No, the cutting speed is steady at approximately 300 RPM. The variable speed dial on the Hub is designed to work with the MAKERX Rotary Tool, Grinder, and Blower. It is ineffective on the Rotary Cutter.
Using a fully charged 2.0Ah 20V Power Share battery, the Rotary Cutter will run for over 2 hours under no-load conditions. The material being cut, feed rate, and other factors can affect the runtime slightly.
The MAKERX ZipSnip Rotary Cutter can handle materials up to ¼ in. thick.
The 20V MAKERX Hot Glue Gun uses mini glue sticks of size .28in., or 7mm. These mini sticks can be found at craft stores, hardware stores and home centers, mass merchants, and online.
First, make sure the battery is charged and all the connections are tight. Turn the variable speed dial on the Hub to min. Push the on switch on the Hub. Hold the on/off button on the Glue Gun for 3 seconds. The button should turn red to indicate the glue is heating. After about 30 seconds, the light should illuminate green, meaning the Glue Gun is hot enough to use.
The indicator light on the 20V Hot Glue Gun turns from red to green when ready to use. After 30 seconds, the temp will be approximately 285°F. After 60 seconds, approximately 345°F. After 90 seconds, approximately 400°F.
The opening for dispensing glue is .05” wide (1.2mm).
The Hot Glue Gun is programmed to turn off after ten minutes. This prevents the glue gun from being left on by accident and helps preserve energy.
No, the speed dial on the Hub is ineffective on the 20V Glue Gun. Leave it on the minimum setting. The speed dial controls the MAKERX
, , and , which are available separately.Use this MAKERX mini blower to clean sawdust and other debris from workspaces, clean small crevices like keyboards, dry materials like paint and glue, and more.
This blower can’t really move leaves off the lawn, no. But it will do a great job blowing pollen off of your wicker furniture, soil off of a potting table, or straw out of a birdhouse.
Yes. Check out Worx.com for the accessory kit of nozzles for the 20V MAKERX Portable Mini Blower,
.600D heavy-duty nylon.
There are moveable dividers inside the case that allow the compartment sizes to be changed.
No, there is no way to lock the case, but there is a latch that will hold the lid closed until someone releases it.
The case has configurable compartments and can hold a large number of accessories. The size of the accessories would affect the quantity count of course.
The accessory case is made from polypropylene. It is a strong and durable but flexible plastic which wears and resists breakage well.


Contrary to popular belief, Lorem Ipsum
Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident laborum.
